T8 bulbs, also known as T8 lamps or T8 TLEDs, are energy-efficient, lumen-boosting replacements for T8 or T12 fluorescent lamps. If you are ready to upgrade your fluorescent lighting to LEDs, T8 TLEDs are a fantastic alternative to buying full LED fixtures. Because LED and fluorescent technologies are so unique, there are a few steps you’ll have to take, but don’t panic: Rewiring a T12 fluorescent luminaire or T8 fluorescent luminaire is simpler than you think. Most locations require the work to be completed by a licensed electrician, and Access Fixtures will always recommend the same, so be sure to check with local regulations to determine the safest way to proceed. For those of you who like to DIY, follow this guide to rewire a T12 or T8 fluorescent luminaire for T8 LED lamps and bypass the existing ballast.
T8 LED Installation Instructions
Confirm that the power source to the luminaire is between 120v and 277v.
Shut off the power going to the light fixture.
Make sure the switch that controls the power to the luminaire does not have a dimmer.
Disconnect the power supply to the fluorescent ballast.
Remove the ballast and starter, if applicable, from the existing fixture.
Remove the existing lamp holders or sockets (these are also commonly known as tombstones).
Install the non-shunted lamp holders in place of the existing, shunted lamp holders. (Non-shunted means that there is no connection between the contacts at the socket. See this photo for how your lamp holders should and should not look.) Using shunted tombstones can fry the sockets and damage the LED lamps, so it is important to identify the differences and use the correct components.
Mark the LIVE END of the fixture using either a permanent marker or a sticker. Note that the lamp holders on the other end will not be wired to anything.
Wire the hot lead to one of the leads on the side marked “LIVE END.”
Wire the neutral lead to the other lead on the LIVE END lamp holder.
Once all the new, non-shunted lamp holders are wired on the LIVE END, reconnect the luminaire to the power source.
Install the new T8 LED lamps, matching the end of the lamp marked “L” to the LIVE END.
Affix a cautionary Lamping Replacement label to the luminaire surface where it is visible during future re-lamping.
Turn the power back on. Your T8 LED lamps should light up!
Once a fixture is wired for T8 LED, you can no longer put fluorescent lamps back into the luminaire. This isn’t an issue, however, because the long-life, energy-efficiency, and reliability of LED lighting makes it the most sensible replacement option.
Speak to an Access Fixtures Lighting Specialist about Choosing the Right Fixture
Are you looking to rewire your fluorescent fixtures for T8 LED lamps? Unsure of what options or lamps to choose? No problem. We’re always happy to help. Speak to an Access Fixtures lighting specialist to discuss some options, or if you need help placing an order, call us at 800-468-9925. Our customer service team is located in Worcester, MA, and is ready to get you the fixtures and lamps you need.
Access Fixtures, a Massachusetts-based commercial and industrial lighting manufacturer, has released a new line of high performing sports lights. The STAJ sports lighter comes equipped with a dial for angling ...
Bollard light replacement parts are beneficial for anyone who owns an Access Fixtures bollard light. These products include inner and outer lenses for square and round bollard lights as well ...
Access Fixtures is no stranger to lighting unusual projects. High-performance lighting solutions is what we do, after all. When a sportsman's club contacted us about lighting a trap and skeet ...
A customer recently contacted our team seeking expert advice from one of our lighting specialists for an environmentally-conscious lighting solution. They needed fixtures that comply with outdoor dark sky lighting ...
Access Fixtures, a Massachusetts-based commercial and industrial lighting manufacturer, has released an updated line of turtle friendly 590nm wall packs. The APTU wall pack emits light in a narrow 590nm ...
Access Fixtures, a Massachusetts-based commercial and industrial lighting manufacturer, has released a new line of high performing sports lights. The STAJ sports lighter comes equipped with a dial for angling ...
Bollard light replacement parts are beneficial for anyone who owns an Access Fixtures bollard light. These products include inner and outer lenses for square and round bollard lights as well ...
Access Fixtures is no stranger to lighting unusual projects. High-performance lighting solutions is what we do, after all. When a sportsman's club contacted us about lighting a trap and skeet ...
A customer recently contacted our team seeking expert advice from one of our lighting specialists for an environmentally-conscious lighting solution. They needed fixtures that comply with outdoor dark sky lighting ...
Access Fixtures, a Massachusetts-based commercial and industrial lighting manufacturer, has released an updated line of turtle friendly 590nm wall packs. The APTU wall pack emits light in a narrow 590nm ...