T8 bulbs, also known as T8 lamps or T8 TLEDs, are energy-efficient, lumen-boosting replacements for T8 or T12 fluorescent lamps. If you are ready to upgrade your fluorescent lighting to LEDs, T8 TLEDs are a fantastic alternative to buying full LED fixtures. Because LED and fluorescent technologies are so unique, there are a few steps you’ll have to take, but don’t panic: Rewiring a T12 fluorescent luminaire or T8 fluorescent luminaire is simpler than you think. Most locations require the work to be completed by a licensed electrician, and Access Fixtures will always recommend the same, so be sure to check with local regulations to determine the safest way to proceed. For those of you who like to DIY, follow this guide to rewire a T12 or T8 fluorescent luminaire for T8 LED lamps and bypass the existing ballast.
T8 LED Installation Instructions
Confirm that the power source to the luminaire is between 120v and 277v.
Shut off the power going to the light fixture.
Make sure the switch that controls the power to the luminaire does not have a dimmer.
Disconnect the power supply to the fluorescent ballast.
Remove the ballast and starter, if applicable, from the existing fixture.
Remove the existing lamp holders or sockets (these are also commonly known as tombstones).
Install the non-shunted lamp holders in place of the existing, shunted lamp holders. (Non-shunted means that there is no connection between the contacts at the socket. See this photo for how your lamp holders should and should not look.) Using shunted tombstones can fry the sockets and damage the LED lamps, so it is important to identify the differences and use the correct components.
Mark the LIVE END of the fixture using either a permanent marker or a sticker. Note that the lamp holders on the other end will not be wired to anything.
Wire the hot lead to one of the leads on the side marked “LIVE END.”
Wire the neutral lead to the other lead on the LIVE END lamp holder.
Once all the new, non-shunted lamp holders are wired on the LIVE END, reconnect the luminaire to the power source.
Install the new T8 LED lamps, matching the end of the lamp marked “L” to the LIVE END.
Affix a cautionary Lamping Replacement label to the luminaire surface where it is visible during future re-lamping.
Turn the power back on. Your T8 LED lamps should light up!
Once a fixture is wired for T8 LED, you can no longer put fluorescent lamps back into the luminaire. This isn’t an issue, however, because the long-life, energy-efficiency, and reliability of LED lighting makes it the most sensible replacement option.
Speak to an Access Fixtures Lighting Specialist about Choosing the Right Fixture
Are you looking to rewire your fluorescent fixtures for T8 LED lamps? Unsure of what options or lamps to choose? No problem. We’re always happy to help. Speak to an Access Fixtures lighting specialist to discuss some options, or if you need help placing an order, call us at 800-468-9925. Our customer service team is located in Worcester, MA, and is ready to get you the fixtures and lamps you need.
WORCESTER, MA, May 2018—If you haven’t replaced your underperforming, inefficient high-pressure sodium (HPS) wall packs with LED, Access Fixtures understands why. For years, LED replacements have only been available in ...
WORCESTER, MA, March 2018—Access Fixtures introduces the APTA LED high bay light series to its expansive, commercial-grade line of LED high bays. These high-powered lighting fixtures deliver 120 lumens/watt for ...
WORCESTER, MA, March 2018—In their continued effort to provide versatile, cutting-edge, and high-performance lighting solutions, Access Fixtures announces brand-new, vandal-proof LED bollard landscape lighting fixtures. The most unique part: These ...
Recently, a customer in California contacted the Access Fixtures lighting experts to inquire about outdoor basketball court LED lighting. His goal was to sufficiently light his backyard court but also ...
WORCESTER, MA, February 2018—Adding to its impressive arsenal of high-performance light bollards, Access Fixtures releases new 20-watt units in CONA, LUVO, and TEFA housing styles. These powerful and stylish LED ...
WORCESTER, MA, May 2018—If you haven’t replaced your underperforming, inefficient high-pressure sodium (HPS) wall packs with LED, Access Fixtures understands why. For years, LED replacements have only been available in ...
WORCESTER, MA, March 2018—Access Fixtures introduces the APTA LED high bay light series to its expansive, commercial-grade line of LED high bays. These high-powered lighting fixtures deliver 120 lumens/watt for ...
WORCESTER, MA, March 2018—In their continued effort to provide versatile, cutting-edge, and high-performance lighting solutions, Access Fixtures announces brand-new, vandal-proof LED bollard landscape lighting fixtures. The most unique part: These ...
Recently, a customer in California contacted the Access Fixtures lighting experts to inquire about outdoor basketball court LED lighting. His goal was to sufficiently light his backyard court but also ...
WORCESTER, MA, February 2018—Adding to its impressive arsenal of high-performance light bollards, Access Fixtures releases new 20-watt units in CONA, LUVO, and TEFA housing styles. These powerful and stylish LED ...