T8 bulbs, also known as T8 lamps or T8 TLEDs, are energy-efficient, lumen-boosting replacements for T8 or T12 fluorescent lamps. If you are ready to upgrade your fluorescent lighting to LEDs, T8 TLEDs are a fantastic alternative to buying full LED fixtures. Because LED and fluorescent technologies are so unique, there are a few steps you’ll have to take, but don’t panic: Rewiring a T12 fluorescent luminaire or T8 fluorescent luminaire is simpler than you think. Most locations require the work to be completed by a licensed electrician, and Access Fixtures will always recommend the same, so be sure to check with local regulations to determine the safest way to proceed. For those of you who like to DIY, follow this guide to rewire a T12 or T8 fluorescent luminaire for T8 LED lamps and bypass the existing ballast.
T8 LED Installation Instructions
Confirm that the power source to the luminaire is between 120v and 277v.
Shut off the power going to the light fixture.
Make sure the switch that controls the power to the luminaire does not have a dimmer.
Disconnect the power supply to the fluorescent ballast.
Remove the ballast and starter, if applicable, from the existing fixture.
Remove the existing lamp holders or sockets (these are also commonly known as tombstones).
Install the non-shunted lamp holders in place of the existing, shunted lamp holders. (Non-shunted means that there is no connection between the contacts at the socket. See this photo for how your lamp holders should and should not look.) Using shunted tombstones can fry the sockets and damage the LED lamps, so it is important to identify the differences and use the correct components.
Mark the LIVE END of the fixture using either a permanent marker or a sticker. Note that the lamp holders on the other end will not be wired to anything.
Wire the hot lead to one of the leads on the side marked “LIVE END.”
Wire the neutral lead to the other lead on the LIVE END lamp holder.
Once all the new, non-shunted lamp holders are wired on the LIVE END, reconnect the luminaire to the power source.
Install the new T8 LED lamps, matching the end of the lamp marked “L” to the LIVE END.
Affix a cautionary Lamping Replacement label to the luminaire surface where it is visible during future re-lamping.
Turn the power back on. Your T8 LED lamps should light up!
Once a fixture is wired for T8 LED, you can no longer put fluorescent lamps back into the luminaire. This isn’t an issue, however, because the long-life, energy-efficiency, and reliability of LED lighting makes it the most sensible replacement option.
Speak to an Access Fixtures Lighting Specialist about Choosing the Right Fixture
Are you looking to rewire your fluorescent fixtures for T8 LED lamps? Unsure of what options or lamps to choose? No problem. We’re always happy to help. Speak to an Access Fixtures lighting specialist to discuss some options, or if you need help placing an order, call us at 800-468-9925. Our customer service team is located in Worcester, MA, and is ready to get you the fixtures and lamps you need.
WORCESTER, MA, November 2017—Access Fixtures launches a new LED wildlife and turtle-friendly lighting bollard light These energy-efficient bollard lights emit an amber-colored light between 585-595 nanometers to meet sea coastal regulations. ...
What Is a 0-10v Dimmer or a 1-10v Dimmer?
0-10v dimming and 1-10v dimming are a lighting control methods that use a low voltage, direct current (DC) circuit between 0 and ...
WORCESTER, MA, November 2017—Access Fixtures launches new VERS LED wall lights. These cutoff LED wall lights can be used for wall-mount applications in retail centers, industrial parks, schools and universities, public ...
Depending on the type and level of play of your specific application, the required light intensity measurement will differ. Illuminance, also known as incident light or brightness, refers to the ...
WORCESTER, MA, November 2017—Access Fixtures announces the newly available 3000K color temperature in a large selection of their bollard and outdoor path lighting fixtures. Now available in 3000K, this warm-white ...
WORCESTER, MA, November 2017—Access Fixtures launches a new LED wildlife and turtle-friendly lighting bollard light These energy-efficient bollard lights emit an amber-colored light between 585-595 nanometers to meet sea coastal regulations. ...
What Is a 0-10v Dimmer or a 1-10v Dimmer?
0-10v dimming and 1-10v dimming are a lighting control methods that use a low voltage, direct current (DC) circuit between 0 and ...
WORCESTER, MA, November 2017—Access Fixtures launches new VERS LED wall lights. These cutoff LED wall lights can be used for wall-mount applications in retail centers, industrial parks, schools and universities, public ...
Depending on the type and level of play of your specific application, the required light intensity measurement will differ. Illuminance, also known as incident light or brightness, refers to the ...
WORCESTER, MA, November 2017—Access Fixtures announces the newly available 3000K color temperature in a large selection of their bollard and outdoor path lighting fixtures. Now available in 3000K, this warm-white ...