T8 bulbs, also known as T8 lamps or T8 TLEDs, are energy-efficient, lumen-boosting replacements for T8 or T12 fluorescent lamps. If you are ready to upgrade your fluorescent lighting to LEDs, T8 TLEDs are a fantastic alternative to buying full LED fixtures. Because LED and fluorescent technologies are so unique, there are a few steps you’ll have to take, but don’t panic: Rewiring a T12 fluorescent luminaire or T8 fluorescent luminaire is simpler than you think. Most locations require the work to be completed by a licensed electrician, and Access Fixtures will always recommend the same, so be sure to check with local regulations to determine the safest way to proceed. For those of you who like to DIY, follow this guide to rewire a T12 or T8 fluorescent luminaire for T8 LED lamps and bypass the existing ballast.
T8 LED Installation Instructions
- Confirm that the power source to the luminaire is between 120v and 277v.
- Shut off the power going to the light fixture.
- Make sure the switch that controls the power to the luminaire does not have a dimmer.
- Disconnect the power supply to the fluorescent ballast.
- Remove the ballast and starter, if applicable, from the existing fixture.
- Remove the existing lamp holders or sockets (these are also commonly known as tombstones).
- Install the non-shunted lamp holders in place of the existing, shunted lamp holders. (Non-shunted means that there is no connection between the contacts at the socket. See this photo for how your lamp holders should and should not look.) Using shunted tombstones can fry the sockets and damage the LED lamps, so it is important to identify the differences and use the correct components.
- Mark the LIVE END of the fixture using either a permanent marker or a sticker. Note that the lamp holders on the other end will not be wired to anything.
- Wire the hot lead to one of the leads on the side marked “LIVE END.”
- Wire the neutral lead to the other lead on the LIVE END lamp holder.
- Be sure to secure all connections with wire nuts.
- Once all the new, non-shunted lamp holders are wired on the LIVE END, reconnect the luminaire to the power source.
- Install the new T8 LED lamps, matching the end of the lamp marked “L” to the LIVE END.
- Affix a cautionary Lamping Replacement label to the luminaire surface where it is visible during future re-lamping.
- Turn the power back on. Your T8 LED lamps should light up!
Once a fixture is wired for T8 LED, you can no longer put fluorescent lamps back into the luminaire. This isn’t an issue, however, because the long-life, energy-efficiency, and reliability of LED lighting makes it the most sensible replacement option.
Speak to an Access Fixtures Lighting Specialist about Choosing the Right Fixture
Are you looking to rewire your fluorescent fixtures for T8 LED lamps? Unsure of what options or lamps to choose? No problem. We’re always happy to help. Speak to an Access Fixtures lighting specialist to discuss some options, or if you need help placing an order, call us at 800-468-9925. Our customer service team is located in Worcester, MA, and is ready to get you the fixtures and lamps you need.
Sorry No Results Found
The page you requested is no longer on the site. Try refining your search using the search box, or use the navigation above to locate the post.
You can also call us at 800-468-9925 or Chat with a Live Certified Lighting Specialist. Or...
Recent Blog Posts
ARCI Bollard Light New Design Feature: ARCI LED Outdoor Lights With GFCI Outlet
WORCESTER, MA August 13, 2024 - Access Fixtures, a leading provider of high-performance LED lighting solutions, proudly announces the introduction of a new design feature to its ARCI LED Bollard ...Outdoor Solar Light Batteries: (LiFePO4) LED Solar Lighting Batteries
As sustainable and energy-efficient lighting solutions are embraced, outdoor solar lighting has become pivotal in commercial applications. At the heart of these advanced lighting systems lies the battery, a crucial ...Access Fixtures Explains LED Non UV Lights vs. Lights With No UV Light Below 450nm
WORCESTER, MA, July 9th, 2024 — Access Fixtures, a leading provider of high-performance LED lighting solutions, is excited to present the differences and applications of LED Non UV Lights versus ...Access Fixtures Attends SEMICON West 2024 Featuring No UV LED Lights
WORCESTER, MA, July 9th, 2024 — Access Fixtures, a leading high-performance LED lighting solutions provider, is excited to feature their innovative No UV LED lights with no light under 450nm ...Solar Light Installation-5 Tips for Installing Integrated Solar Lights
Integrated solar area lights are gaining popularity as contemporary outdoor lighting solutions due to their compact, stylish, and lightweight designs. With advancements in solar lighting technology, these lights offer cost-effective ...Class 2 Div 1 Lighting – LED Lighting | Class 2 Division 1 Lights
Class 2 Div 1 lighting maintains safety in hazardous areas, where flammable gases, vapors, combustible dust, or easily ignitable fibers exist
Food Processing Facilities Gain LED Lighting Option with NSF Sanitation Certified T8 LEDs
With their newly acquired NSF sanitation certification, Forest Lighting’s LED products can now provide long-term energy savings to the food processing industry! Forest Lighting, the USA branch of worldwide LED manufacturer MLS distributed by Access Fixtures, has...