T8 bulbs, also known as T8 lamps or T8 TLEDs, are energy-efficient, lumen-boosting replacements for T8 or T12 fluorescent lamps. If you are ready to upgrade your fluorescent lighting to LEDs, T8 TLEDs are a fantastic alternative to buying full LED fixtures. Because LED and fluorescent technologies are so unique, there are a few steps you’ll have to take, but don’t panic: Rewiring a T12 fluorescent luminaire or T8 fluorescent luminaire is simpler than you think. Most locations require the work to be completed by a licensed electrician, and Access Fixtures will always recommend the same, so be sure to check with local regulations to determine the safest way to proceed. For those of you who like to DIY, follow this guide to rewire a T12 or T8 fluorescent luminaire for T8 LED lamps and bypass the existing ballast.
T8 LED Installation Instructions
- Confirm that the power source to the luminaire is between 120v and 277v.
- Shut off the power going to the light fixture.
- Make sure the switch that controls the power to the luminaire does not have a dimmer.
- Disconnect the power supply to the fluorescent ballast.
- Remove the ballast and starter, if applicable, from the existing fixture.
- Remove the existing lamp holders or sockets (these are also commonly known as tombstones).
- Install the non-shunted lamp holders in place of the existing, shunted lamp holders. (Non-shunted means that there is no connection between the contacts at the socket. See this photo for how your lamp holders should and should not look.) Using shunted tombstones can fry the sockets and damage the LED lamps, so it is important to identify the differences and use the correct components.
- Mark the LIVE END of the fixture using either a permanent marker or a sticker. Note that the lamp holders on the other end will not be wired to anything.
- Wire the hot lead to one of the leads on the side marked “LIVE END.”
- Wire the neutral lead to the other lead on the LIVE END lamp holder.
- Be sure to secure all connections with wire nuts.
- Once all the new, non-shunted lamp holders are wired on the LIVE END, reconnect the luminaire to the power source.
- Install the new T8 LED lamps, matching the end of the lamp marked “L” to the LIVE END.
- Affix a cautionary Lamping Replacement label to the luminaire surface where it is visible during future re-lamping.
- Turn the power back on. Your T8 LED lamps should light up!
Once a fixture is wired for T8 LED, you can no longer put fluorescent lamps back into the luminaire. This isn’t an issue, however, because the long-life, energy-efficiency, and reliability of LED lighting makes it the most sensible replacement option.
Speak to an Access Fixtures Lighting Specialist about Choosing the Right Fixture
Are you looking to rewire your fluorescent fixtures for T8 LED lamps? Unsure of what options or lamps to choose? No problem. We’re always happy to help. Speak to an Access Fixtures lighting specialist to discuss some options, or if you need help placing an order, call us at 800-468-9925. Our customer service team is located in Worcester, MA, and is ready to get you the fixtures and lamps you need.
Sorry No Results Found
The page you requested is no longer on the site. Try refining your search using the search box, or use the navigation above to locate the post.
You can also call us at 800-468-9925 or Chat with a Live Certified Lighting Specialist. Or...
Recent Blog Posts
Explosion Proof Light Fixtures – Mounting Options for Lighting Fixtures
Explosion-proof light fixtures are vital in maintaining safety in environments with hazardous materials where any ignition could be catastrophic. The effectiveness of these fixtures is significantly influenced by their mounting ...Explosion Proof LEDs | 590nm LED Explosion Proof Lights | Explosion-Proof LED Lighting
In coastal regions, the need for specialized lighting solutions that meet strict regulatory requirements is critical not only for human safety but also for environmental conservation. Explosion proof LED lights ...Explosion Proof LED Lamp – Explosion-Proof LED Lighting – LED Explosion Proof Light
In environments where explosive atmospheres exist, the selection of appropriate LED lighting fixtures is critical. Explosion proof LED lamps are specially designed to prevent the ignition of surrounding flammable gases, ...Explosion Proof Lighting LED HazLoc Classes for Explosion Proof Lights
In industries where flammable substances are processed, stored, or used, the proper classification of locations for explosion proof lights is crucial. This detailed guide explores the classification of hazardous locations ...Explosion Proof LED Lights – LED Explosion-Proof Lighting Applications
Explosion proof LED lighting is vital in industries where hazardous atmospheres pose a constant risk due to explosive gases, vapors, or dust. These specialized lighting solutions are engineered to prevent ...Explosion Proof LED Lamp – Explosion-Proof LED Lighting – LED Explosion Proof Light
Explore the construction and materials of the explosion proof LED lamp, including comparisons between glass and polycarbonate lenses.
Sorry No Results Found
The page you requested is no longer on the site. Try refining your search using the search box, or use the navigation above to locate the post.
You can also call us at 800-468-9925 or Chat with a Live Certified Lighting Specialist. Or...